Colin Hanks

Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are easy to maintain and durable, as well as long-lasting. They do not rot or rust like timber and aluminum.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will reduce unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and may even be fatal. It is essential to take the time to ensure that you are doing everything you can to keep your windows in good condition.

For single pane windows it can be relatively simple to replace windows, and the new one will usually fit inside the frame that was previously installed easily. However If you have double-pane windows that are held in place by internal beading, it will be more difficult to get rid of the panes that are in place and replace them with new ones. In this situation you'll need source some plastic spacers that will assist the new pane to fit perfectly into the frame of the window.

Wearing protective eyewear and thick gloves is a must when you are planning to remove the glass yourself. You should also lay down a dropcloth prior to you begin working on the window panes so that any shards fall on the fabric, not onto the floor which could cause them to be trampled under.

After the glass has been removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to stop drafts and water from entering the property until a professional comes out and repair the window. It also acts as an obstruction to prevent criminals from getting into your home. If the gap is particularly large, you might think about an alarm door that comes with an integrated window repair, since it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows with sash. In time, they could be affected by a variety of issues such as sagging. A window that is sagging can cause problems with light, draughts and even security. It is crucial to act when you notice your upvc window repairs windows are falling down.

Repositioning the hinges could aid in fixing a window that is sliding. First, you'll need to unblock the windows to get at the frame. With a screwdriver, you can take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Once you've adjusted the hinges, close your window and verify the fit. If you're happy with the fit, you can tighten the screws to ensure they remain in place.

If you are unable to reposition the hinges you may need to replace the seal. Rubber seals may dry out and lose their elasticity over time, which causes them to loose their elasticity. It is important to replace your seal as soon as you can to ensure that your uPVC window waterproof and draughtproof.

UPVC handles can also become loose. This is often caused by screws that have become undone over time, but it can be due to the mechanism of the handle wearing out. It's fairly simple to fix a loose uPVC hand. The first step is to close the window and then perform an experiment fit. The joint at the corners of the sash must align with the joint on the casing. If it does not you can use a screwdriver to loosen the handle. Then, turn the mechanism to position.

3. Water Leaks

If you're waking up to wet floors and mouldy walls every time it rains it's crucial to take action. Water leaks through windows can cause structural damage to your home and impact your ability to regulate the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be done by any DIY expert. Depending on the severity of the issue is, old caulking may have to be removed. It is important to keep in mind that when it comes to uPVC window repairs you should avoid the temptation to "over-caulk and then make the area more difficult to clean and can reduce your energy efficiency.

It is essential to ensure that any drainage holes are free of debris and that the sill pan is angled correctly so that it drains away from the window. In more serious situations, you might have to consider replacing the window.

Mold spots and rotted sills are another sign of water leakage. The is a fungus that thrives in damp conditions and is able to quickly spread throughout the house.

It is also important to remember that if the leakage originates from the glass of your double-glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or sagging. It is also possible to be corrected by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be the reason for the reason that your uPVC window is difficult to open or it opens with a breeze. These are easily repaired by any DIYer who is skilled and are usually completed in just a few minutes.

Like any mechanical part hinges will be damaged over time. It's very simple to change a window hinge however it is easier if someone helps you hold the frame.

It is also important to ensure that the uPVC hinges are being opened and closed in the correct direction. You can do this by looking for the arrows on each hinge, this shows which way the window should open.

Window hinges that aren't working properly could be caused by improperly opening the window repair near me a certain way or by improper installation in the factory. This issue can be fixed by sending us a photo on our website. We will be pleased to offer you advice.

It is also essential to ensure that the hinges are lubricated regularly. This can be done by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window to open and close more easily. It also decreases the chance of windows getting stuck and stop corrosion. Ideally, you should do this at least once a year. WD40 and other solvent based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by different things. The hinges can also be unbalanced due to wear, causing gaps between the frame and sash. These can be easily repaired by giving them good clean, but when they're beyond repair, it might be necessary to have them aligned or replaced. Second, the interlock can be misaligned. This is located on the hinge's side and might require to be cleaned. In certain instances it might be necessary to replace them.

The next most common reason for draughts is window seals. They are susceptible to being worn out or damaged over time, and allow air to escape through the gaps. Installing high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the upvc window with low-emissivity glass, this will help to regulate indoor temperatures and will reduce draughts.

The final method to cut down on the amount of draughts is to use a draught-excluder. These are usually fabric tubes filled with a filler which can be put on top of your window sill. They can keep your home warm by blocking out cold air.

With a bit of regular maintenance and repair your windows made of upvc will continue to provide excellent security and insulation for your home. It is essential to remember that all windows eventually wear out and it may be more cost-effective to simply replace them than to repair them. So, if you are experiencing problems with your upvc windows, it is always recommended to seek assistance from a professional immediately.